Geometric estimates exclude rolling tolerances, coatings and process losses; hollow and rolled-section references include their own section-table basis. Calculated bar weights use unrounded mass. Values are not measured shipment weights. Confirm length, grade, manufacturing route, packing and supply in the offer; the existing image illustrates the product family.
I-beams have a central web and two flanges; specify the complete series and designation for structural orders.
Parallel-flange IPE beams for structural and fabrication enquiries. Review the exact section dimensions, steel grade and length.Read more
Standards and applicability
Use the exact series and section table: EN 10365 dimensions, EN 10034 I/H tolerances or EN 10279 channel tolerances; a UE/GOST 8240 section is not automatically UPN. Material references below are EN 10025-2, with the actual web/flange thickness band where known. The hub compares 3 < t ≤ 63 mm bands. Tensile/yield values do not establish member capacity. Elongation, orientation, impact specimen and acceptance conditions require the complete order specification.
Mechanical reference table
Mechanical reference table
Grade / material
Scope / condition
Re / Rp0.2 (MPa)
Rm (MPa)
A min. (%)
Impact reference
S235JR
3 < t ≤ 16 mm
≥235
360–510
—
27 J / +20°C
S235JR
16 < t ≤ 40 mm
≥225
360–510
—
27 J / +20°C
S235JR
40 < t ≤ 63 mm
≥215
360–510
—
27 J / +20°C
S275JR
3 < t ≤ 16 mm
≥275
410–560
—
27 J / +20°C
S275JR
16 < t ≤ 40 mm
≥265
410–560
—
27 J / +20°C
S275JR
40 < t ≤ 63 mm
≥255
410–560
—
27 J / +20°C
S355J2
3 < t ≤ 16 mm
≥355
470–630
—
27 J / −20°C
S355J2
16 < t ≤ 40 mm
≥345
470–630
—
27 J / −20°C
S355J2
40 < t ≤ 63 mm
≥335
470–630
—
27 J / −20°C
Chemical composition references
Chemical composition references
Grade / material
Scope / condition
C (%)
Mn (%)
Si (%)
P (%)
S (%)
Cr / CEV (%)
S235JR
3 < t ≤ 16 mm
≤0.17
≤1.40
—
≤0.035
≤0.035
—
S235JR
16 < t ≤ 40 mm
≤0.17
≤1.40
—
≤0.035
≤0.035
—
S235JR
40 < t ≤ 63 mm
≤0.20
≤1.40
—
≤0.035
≤0.035
—
S275JR
3 < t ≤ 16 mm
≤0.21
≤1.50
—
≤0.035
≤0.035
—
S275JR
16 < t ≤ 40 mm
≤0.21
≤1.50
—
≤0.035
≤0.035
—
S275JR
40 < t ≤ 63 mm
≤0.22
≤1.50
—
≤0.035
≤0.035
—
S355J2
3 < t ≤ 16 mm
≤0.20
≤1.60
≤0.55
≤0.025
≤0.025
—
S355J2
16 < t ≤ 40 mm
≤0.20
≤1.60
≤0.55
≤0.025
≤0.025
—
S355J2
40 < t ≤ 63 mm
≤0.22
≤1.60
≤0.55
≤0.025
≤0.025
—
Selected percentages by mass and test values are reference requirements within the stated scope, not the actual heat analysis or a complete specification. A dash means no value is declared here, not zero. Compare the offered heat and test results with the applicable specification and inspection document. If EN 10204 type 3.1 is required, agree document availability, heat traceability and test scope before ordering.
Inspection and export enquiry
Send the exact product, size, full grade and standard edition, delivery condition, quantity, test requirements and named destination. Confirm cutting, coating, bundle or coil mass, protection, unloading and the Incoterms delivery point in the quotation. The destination guidance below supports port and inland comparisons; it does not confirm local stock or a fixed price.
Chemistry references and commercial grades
St37, St44 and St52 · historical DIN 17100 reference
Ladle-analysis reference for St37-2, St44-2 and St52-3 at t ≤16 mm only. Bare St37/St44/St52 names need a suffix, edition and delivery condition. Other thicknesses and product analysis have different rules. These legacy grades are not automatically equivalent to EN grades or interchangeable with CK45/CK60. For semi-finished feedstock, agree chemistry and downstream qualification separately.
St37, St44 and St52 · historical DIN 17100 reference
Grade / commercial type
C (%)
Mn (%)
Si (%)
P (%)
S (%)
St37-2 / 1.0037
≤0.17
—
—
≤0.050
≤0.050
St44-2 / 1.0044
≤0.21
—
—
≤0.050
≤0.050
St52-3 / 1.0570
≤0.20
≤1.60
≤0.55
≤0.040
≤0.040
Reference values are not shipment analysis or an inventory promise. Agree the complete specification, sampling basis, test methods and acceptance limits before ordering; confirm actual results on the heat/lot certificate. A dash means no numeric limit is stated in this selected reference, not zero.
IPE steel beams Technical and buying guide
Parallel-flange IPE beams for structural and fabrication enquiries. Review the exact section dimensions, steel grade and length.
I-beams have a central web and two flanges; specify the complete series and designation for structural orders.
Specification and dimensions
I-beams: exact series and designation such as IPE, plus nominal height and required length. Where ordering by a drawing, provide flange width, web thickness and flange thickness. Do not treat IPE, IPN or a modified beam as equivalent solely by nominal height.
Grades and applicable standards
Dimensions: EN 10365; tolerances on shape and dimensions: EN 10034. Specify the full material grade separately, for example S235JR, S275JR or S355J2 to EN 10025-2, together with the required inspection documents. HEA and HEB of the same nominal size have different actual dimensions, thicknesses and mass. The designation number is not always the actual section height. IPE, HEA and HEB are separate series; confirm the section table, required length, quantity and delivery destination with EMRA Steel.
Applications and project requirements
I-beams are used in structural framing and supporting members. Section selection must follow the design, including span, loads, connections and lateral restraint.
Inspection and traceability
Agree heat or batch identification, chemical analysis, applicable tests and dimensional checks before ordering. Specify inspection documents, acceptance criteria and any independent inspection requirements.
Sizes, weights and quotation guidance
IPE 80
IPE 80 has an actual section height of 80 mm, flange width 46 mm, web thickness 3.8 mm and flange thickness 5.2 mm. Reference mass is approximately 6 kg/m; calculated weights are 36 kg for a 6 m length and 72 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 80
IPE 100
IPE 100 has an actual section height of 100 mm, flange width 55 mm, web thickness 4.1 mm and flange thickness 5.7 mm. Reference mass is approximately 8.1 kg/m; calculated weights are 48.6 kg for a 6 m length and 97.2 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 100
IPE 120
IPE 120 has an actual section height of 120 mm, flange width 64 mm, web thickness 4.4 mm and flange thickness 6.3 mm. Reference mass is approximately 10.4 kg/m; calculated weights are 62.4 kg for a 6 m length and 124.8 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 120
IPE 140
IPE 140 has an actual section height of 140 mm, flange width 73 mm, web thickness 4.7 mm and flange thickness 6.9 mm. Reference mass is approximately 12.9 kg/m; calculated weights are 77.4 kg for a 6 m length and 154.8 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 140
IPE 160
IPE 160 has an actual section height of 160 mm, flange width 82 mm, web thickness 5 mm and flange thickness 7.4 mm. Reference mass is approximately 15.8 kg/m; calculated weights are 94.8 kg for a 6 m length and 189.6 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 160
IPE 180
IPE 180 has an actual section height of 180 mm, flange width 91 mm, web thickness 5.3 mm and flange thickness 8 mm. Reference mass is approximately 18.8 kg/m; calculated weights are 112.8 kg for a 6 m length and 225.6 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 180
IPE 200
IPE 200 has an actual section height of 200 mm, flange width 100 mm, web thickness 5.6 mm and flange thickness 8.5 mm. Reference mass is approximately 22.4 kg/m; calculated weights are 134.4 kg for a 6 m length and 268.8 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 200
IPE 220
IPE 220 has an actual section height of 220 mm, flange width 110 mm, web thickness 5.9 mm and flange thickness 9.2 mm. Reference mass is approximately 26.2 kg/m; calculated weights are 157.2 kg for a 6 m length and 314.4 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 220
IPE 240
IPE 240 has an actual section height of 240 mm, flange width 120 mm, web thickness 6.2 mm and flange thickness 9.8 mm. Reference mass is approximately 30.7 kg/m; calculated weights are 184.2 kg for a 6 m length and 368.4 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 240
IPE 270
IPE 270 has an actual section height of 270 mm, flange width 135 mm, web thickness 6.6 mm and flange thickness 10.2 mm. Reference mass is approximately 36.1 kg/m; calculated weights are 216.6 kg for a 6 m length and 433.2 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 270
IPE 300
IPE 300 has an actual section height of 300 mm, flange width 150 mm, web thickness 7.1 mm and flange thickness 10.7 mm. Reference mass is approximately 42.2 kg/m; calculated weights are 253.2 kg for a 6 m length and 506.4 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 300
IPE 330
IPE 330 has an actual section height of 330 mm, flange width 160 mm, web thickness 7.5 mm and flange thickness 11.5 mm. Reference mass is approximately 49.1 kg/m; calculated weights are 294.6 kg for a 6 m length and 589.2 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 330
IPE 360
IPE 360 has an actual section height of 360 mm, flange width 170 mm, web thickness 8 mm and flange thickness 12.7 mm. Reference mass is approximately 57.1 kg/m; calculated weights are 342.6 kg for a 6 m length and 685.2 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 360
IPE 400
IPE 400 has an actual section height of 400 mm, flange width 180 mm, web thickness 8.6 mm and flange thickness 13.5 mm. Reference mass is approximately 66.3 kg/m; calculated weights are 397.8 kg for a 6 m length and 795.6 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 400
IPE 450
IPE 450 has an actual section height of 450 mm, flange width 190 mm, web thickness 9.4 mm and flange thickness 14.6 mm. Reference mass is approximately 77.6 kg/m; calculated weights are 465.6 kg for a 6 m length and 931.2 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 450
IPE 500
IPE 500 has an actual section height of 500 mm, flange width 200 mm, web thickness 10.2 mm and flange thickness 16 mm. Reference mass is approximately 90.7 kg/m; calculated weights are 544.2 kg for a 6 m length and 1088.4 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 500
IPE 550
IPE 550 has an actual section height of 550 mm, flange width 210 mm, web thickness 11.1 mm and flange thickness 17.2 mm. Reference mass is approximately 106 kg/m; calculated weights are 636 kg for a 6 m length and 1272 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 550
IPE 600
IPE 600 has an actual section height of 600 mm, flange width 220 mm, web thickness 12 mm and flange thickness 19 mm. Reference mass is approximately 122 kg/m; calculated weights are 732 kg for a 6 m length and 1464 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. IPE 600
Frequently asked questions
Does an example mean immediate availability?
No. Examples are enquiry references; stock and delivery must be confirmed for the complete specification.
Can a different grade or standard be substituted?
Only after the proposed material and the project requirements have been technically reviewed.
Quotation requirements
For an I-beam quotation, provide the exact IPE or other designated section, length, grade and quantity. Additional cutting or fabrication and delivery affect the offer. Get a quote
Choose the product specification first; destination and shipment details belong in the delivery enquiry. Destination enquiry guides
Grade enquiries for IPE steel beams
IPE steel beams S235JR
For IPE steel beams S235JR, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
IPE steel beams S275JR
For IPE steel beams S275JR, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
IPE steel beams S355J2
For IPE steel beams S355J2, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
