Geometric estimates exclude rolling tolerances, coatings and process losses; hollow and rolled-section references include their own section-table basis. Calculated bar weights use unrounded mass. Values are not measured shipment weights. Confirm length, grade, manufacturing route, packing and supply in the offer; the existing image illustrates the product family.
H-beams are structural sections; HEA and HEB designations describe different section series and are not interchangeable by nominal height alone.
HEB wide-flange beams: compare the heavier HE series using its own dimensions and weights, separately from HEA.Read more
Standards and applicability
Use the exact series and section table: EN 10365 dimensions, EN 10034 I/H tolerances or EN 10279 channel tolerances; a UE/GOST 8240 section is not automatically UPN. Material references below are EN 10025-2, with the actual web/flange thickness band where known. The hub compares 3 < t ≤ 63 mm bands. Tensile/yield values do not establish member capacity. Elongation, orientation, impact specimen and acceptance conditions require the complete order specification.
Mechanical reference table
Mechanical reference table
Grade / material
Scope / condition
Re / Rp0.2 (MPa)
Rm (MPa)
A min. (%)
Impact reference
S235JR
3 < t ≤ 16 mm
≥235
360–510
—
27 J / +20°C
S235JR
16 < t ≤ 40 mm
≥225
360–510
—
27 J / +20°C
S235JR
40 < t ≤ 63 mm
≥215
360–510
—
27 J / +20°C
S275JR
3 < t ≤ 16 mm
≥275
410–560
—
27 J / +20°C
S275JR
16 < t ≤ 40 mm
≥265
410–560
—
27 J / +20°C
S275JR
40 < t ≤ 63 mm
≥255
410–560
—
27 J / +20°C
S355J2
3 < t ≤ 16 mm
≥355
470–630
—
27 J / −20°C
S355J2
16 < t ≤ 40 mm
≥345
470–630
—
27 J / −20°C
S355J2
40 < t ≤ 63 mm
≥335
470–630
—
27 J / −20°C
Chemical composition references
Chemical composition references
Grade / material
Scope / condition
C (%)
Mn (%)
Si (%)
P (%)
S (%)
Cr / CEV (%)
S235JR
3 < t ≤ 16 mm
≤0.17
≤1.40
—
≤0.035
≤0.035
—
S235JR
16 < t ≤ 40 mm
≤0.17
≤1.40
—
≤0.035
≤0.035
—
S235JR
40 < t ≤ 63 mm
≤0.20
≤1.40
—
≤0.035
≤0.035
—
S275JR
3 < t ≤ 16 mm
≤0.21
≤1.50
—
≤0.035
≤0.035
—
S275JR
16 < t ≤ 40 mm
≤0.21
≤1.50
—
≤0.035
≤0.035
—
S275JR
40 < t ≤ 63 mm
≤0.22
≤1.50
—
≤0.035
≤0.035
—
S355J2
3 < t ≤ 16 mm
≤0.20
≤1.60
≤0.55
≤0.025
≤0.025
—
S355J2
16 < t ≤ 40 mm
≤0.20
≤1.60
≤0.55
≤0.025
≤0.025
—
S355J2
40 < t ≤ 63 mm
≤0.22
≤1.60
≤0.55
≤0.025
≤0.025
—
Selected percentages by mass and test values are reference requirements within the stated scope, not the actual heat analysis or a complete specification. A dash means no value is declared here, not zero. Compare the offered heat and test results with the applicable specification and inspection document. If EN 10204 type 3.1 is required, agree document availability, heat traceability and test scope before ordering.
Inspection and export enquiry
Send the exact product, size, full grade and standard edition, delivery condition, quantity, test requirements and named destination. Confirm cutting, coating, bundle or coil mass, protection, unloading and the Incoterms delivery point in the quotation. The destination guidance below supports port and inland comparisons; it does not confirm local stock or a fixed price.
Chemistry references and commercial grades
St37, St44 and St52 · historical DIN 17100 reference
Ladle-analysis reference for St37-2, St44-2 and St52-3 at t ≤16 mm only. Bare St37/St44/St52 names need a suffix, edition and delivery condition. Other thicknesses and product analysis have different rules. These legacy grades are not automatically equivalent to EN grades or interchangeable with CK45/CK60. For semi-finished feedstock, agree chemistry and downstream qualification separately.
St37, St44 and St52 · historical DIN 17100 reference
Grade / commercial type
C (%)
Mn (%)
Si (%)
P (%)
S (%)
St37-2 / 1.0037
≤0.17
—
—
≤0.050
≤0.050
St44-2 / 1.0044
≤0.21
—
—
≤0.050
≤0.050
St52-3 / 1.0570
≤0.20
≤1.60
≤0.55
≤0.040
≤0.040
Reference values are not shipment analysis or an inventory promise. Agree the complete specification, sampling basis, test methods and acceptance limits before ordering; confirm actual results on the heat/lot certificate. A dash means no numeric limit is stated in this selected reference, not zero.
HEB wide-flange beams: compare the heavier HE series using its own dimensions and weights, separately from HEA.
H-beams are structural sections; HEA and HEB designations describe different section series and are not interchangeable by nominal height alone.
Specification and dimensions
H-beams: exact series and designation such as HEA 100 or HEB 200, plus length. Confirm overall height, flange width, web thickness and flange thickness against the specified section table. HEA and HEB have different dimensions and mass; equal-angle leg dimensions do not apply.
Grades and applicable standards
Dimensions: EN 10365; tolerances on shape and dimensions: EN 10034. Specify the full material grade separately, for example S235JR, S275JR or S355J2 to EN 10025-2, together with the required inspection documents. HEA and HEB of the same nominal size have different actual dimensions, thicknesses and mass. The designation number is not always the actual section height. IPE, HEA and HEB are separate series; confirm the section table, required length, quantity and delivery destination with EMRA Steel.
Applications and project requirements
H-beams are used in structural columns, frames and other designed members. The exact HE series, section properties and connection requirements must be selected from the project specification.
Inspection and traceability
Agree heat or batch identification, chemical analysis, applicable tests and dimensional checks before ordering. Specify inspection documents, acceptance criteria and any independent inspection requirements.
Sizes, weights and quotation guidance
HEB 100
HEB 100 has an actual section height of 100 mm, flange width 100 mm, web thickness 6 mm and flange thickness 10 mm. Reference mass is approximately 20.4 kg/m; calculated weights are 122.4 kg for a 6 m length and 244.8 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 100
HEB 120
HEB 120 has an actual section height of 120 mm, flange width 120 mm, web thickness 6.5 mm and flange thickness 11 mm. Reference mass is approximately 26.7 kg/m; calculated weights are 160.2 kg for a 6 m length and 320.4 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 120
HEB 140
HEB 140 has an actual section height of 140 mm, flange width 140 mm, web thickness 7 mm and flange thickness 12 mm. Reference mass is approximately 33.7 kg/m; calculated weights are 202.2 kg for a 6 m length and 404.4 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 140
HEB 160
HEB 160 has an actual section height of 160 mm, flange width 160 mm, web thickness 8 mm and flange thickness 13 mm. Reference mass is approximately 42.6 kg/m; calculated weights are 255.6 kg for a 6 m length and 511.2 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 160
HEB 180
HEB 180 has an actual section height of 180 mm, flange width 180 mm, web thickness 8.5 mm and flange thickness 14 mm. Reference mass is approximately 51.2 kg/m; calculated weights are 307.2 kg for a 6 m length and 614.4 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 180
HEB 200
HEB 200 has an actual section height of 200 mm, flange width 200 mm, web thickness 9 mm and flange thickness 15 mm. Reference mass is approximately 61.3 kg/m; calculated weights are 367.8 kg for a 6 m length and 735.6 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 200
HEB 220
HEB 220 has an actual section height of 220 mm, flange width 220 mm, web thickness 9.5 mm and flange thickness 16 mm. Reference mass is approximately 71.5 kg/m; calculated weights are 429 kg for a 6 m length and 858 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 220
HEB 240
HEB 240 has an actual section height of 240 mm, flange width 240 mm, web thickness 10 mm and flange thickness 17 mm. Reference mass is approximately 83.2 kg/m; calculated weights are 499.2 kg for a 6 m length and 998.4 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 240
HEB 260
HEB 260 has an actual section height of 260 mm, flange width 260 mm, web thickness 10 mm and flange thickness 17.5 mm. Reference mass is approximately 93 kg/m; calculated weights are 558 kg for a 6 m length and 1116 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 260
HEB 280
HEB 280 has an actual section height of 280 mm, flange width 280 mm, web thickness 10.5 mm and flange thickness 18 mm. Reference mass is approximately 103 kg/m; calculated weights are 618 kg for a 6 m length and 1236 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 280
HEB 300
HEB 300 has an actual section height of 300 mm, flange width 300 mm, web thickness 11 mm and flange thickness 19 mm. Reference mass is approximately 117 kg/m; calculated weights are 702 kg for a 6 m length and 1404 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 300
HEB 320
HEB 320 has an actual section height of 320 mm, flange width 300 mm, web thickness 11.5 mm and flange thickness 20.5 mm. Reference mass is approximately 127 kg/m; calculated weights are 762 kg for a 6 m length and 1524 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 320
HEB 340
HEB 340 has an actual section height of 340 mm, flange width 300 mm, web thickness 12 mm and flange thickness 21.5 mm. Reference mass is approximately 134 kg/m; calculated weights are 804 kg for a 6 m length and 1608 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 340
HEB 360
HEB 360 has an actual section height of 360 mm, flange width 300 mm, web thickness 12.5 mm and flange thickness 22.5 mm. Reference mass is approximately 142 kg/m; calculated weights are 852 kg for a 6 m length and 1704 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 360
HEB 400
HEB 400 has an actual section height of 400 mm, flange width 300 mm, web thickness 13.5 mm and flange thickness 24 mm. Reference mass is approximately 155 kg/m; calculated weights are 930 kg for a 6 m length and 1860 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 400
HEB 450
HEB 450 has an actual section height of 450 mm, flange width 300 mm, web thickness 14 mm and flange thickness 26 mm. Reference mass is approximately 171 kg/m; calculated weights are 1026 kg for a 6 m length and 2052 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 450
HEB 500
HEB 500 has an actual section height of 500 mm, flange width 300 mm, web thickness 14.5 mm and flange thickness 28 mm. Reference mass is approximately 187 kg/m; calculated weights are 1122 kg for a 6 m length and 2244 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 500
HEB 550
HEB 550 has an actual section height of 550 mm, flange width 300 mm, web thickness 15 mm and flange thickness 29 mm. Reference mass is approximately 199 kg/m; calculated weights are 1194 kg for a 6 m length and 2388 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 550
HEB 600
HEB 600 has an actual section height of 600 mm, flange width 300 mm, web thickness 15.5 mm and flange thickness 30 mm. Reference mass is approximately 212 kg/m; calculated weights are 1272 kg for a 6 m length and 2544 kg for a 12 m length. Request 6 m, 12 m or agreed cut lengths, subject to supply confirmation. State the exact series when requesting a price; actual delivery weight depends on rolling tolerances and the agreed weighing basis. HEB 600
Frequently asked questions
Does an example mean immediate availability?
No. Examples are enquiry references; stock and delivery must be confirmed for the complete specification.
Can a different grade or standard be substituted?
Only after the proposed material and the project requirements have been technically reviewed.
Quotation requirements
For an H-beam quotation, provide HEA, HEB or the specified series, nominal designation, length, grade and quantity. Compare prices only for matching series and specifications. Get a quote
Choose the product specification first; destination and shipment details belong in the delivery enquiry. Destination enquiry guides
Grade enquiries for HEB steel beams
HEB steel beams S235JR
For HEB steel beams S235JR, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
HEB steel beams S275JR
For HEB steel beams S275JR, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
HEB steel beams S355J2
For HEB steel beams S355J2, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
