Review Square hollow sections for the 120 × 120 × 6 mm specification. Check material grade, dimensions, inspection documents and delivery requirements before requesting a quotation.
Geometric estimates exclude rolling tolerances, coatings and process losses; hollow and rolled-section references include their own section-table basis. Calculated bar weights use unrounded mass. Values are not measured shipment weights. Confirm length, grade, manufacturing route, packing and supply in the offer; the existing image illustrates the product family.
120 × 120 × 6 mm: outside height 120 mm, outside width 120 mm and nominal wall thickness 6 mm. Reference mass approximately 20.8 kg/m (EN 10219 reference geometry); calculated weights are 124.8 kg for 6 m and 249.6 kg for 12 m. Request 6 m, 12 m or agreed cut lengths, subject to confirmation. Actual weight depends on dimensional tolerances and the supplied section; confirm the mill table and weighing basis. 120 × 120 × 6 mm
Square hollow sections 120 × 120 × 6 mm Technical and buying guide
EMRA Steel
Review Square hollow sections for the 120 × 120 × 6 mm specification. Check material grade, dimensions, inspection documents and delivery requirements before requesting a quotation.Read more
Standards and applicability
Keep EN 10219 cold-formed welded and EN 10210 hot-finished routes separate. Numeric S355J2H rows below are EN 10219 references for t ≤ 16 mm, not automatic EN 10210 or S355NH data. The tensile band changes below 3 mm. Elongation is reduced from 20% to 18% where D/t < 15 for CHS or (B+H)/(2t) < 12.5 for RHS/SHS; below 3 mm confirm gauge length and specimen width. The 27 J at −20°C reference requires the applicable impact-testing and subsize rules. Confirm grade, wall, corner geometry, weld inspection and certificate for the actual route.
Mechanical reference table
Mechanical reference table
Grade / material
Scope / condition
Re / Rp0.2 (MPa)
Rm (MPa)
A min. (%)
Impact reference
S355J2H
EN 10219; 3 ≤ t ≤ 16 mm
≥355
470–630
20 / 18*
27 J / −20°C
Chemical composition references
Chemical composition references
Grade / material
Scope / condition
C (%)
Mn (%)
Si (%)
P (%)
S (%)
Cr / CEV (%)
S355J2H
EN 10219; t ≤ 16 mm
≤0.22
≤1.60
≤0.55
≤0.030
≤0.030
CEV ≤0.45
Selected percentages by mass and test values are reference requirements within the stated scope, not the actual heat analysis or a complete specification. A dash means no value is declared here, not zero. Compare the offered heat and test results with the applicable specification and inspection document. If EN 10204 type 3.1 is required, agree document availability, heat traceability and test scope before ordering.
Inspection and export enquiry
Send the exact product, size, full grade and standard edition, delivery condition, quantity, test requirements and named destination. Confirm cutting, coating, bundle or coil mass, protection, unloading and the Incoterms delivery point in the quotation. The destination guidance below supports port and inland comparisons; it does not confirm local stock or a fixed price.
120 × 120 × 6 mm: outside height 120 mm, outside width 120 mm and nominal wall thickness 6 mm. Reference mass approximately 20.8 kg/m (EN 10219 reference geometry); calculated weights are 124.8 kg for 6 m and 249.6 kg for 12 m. Request 6 m, 12 m or agreed cut lengths, subject to confirmation. Actual weight depends on dimensional tolerances and the supplied section; confirm the mill table and weighing basis. 120 × 120 × 6 mm
Choosing this specification
For 120 × 120 × 6 mm, check outside dimensions, wall thickness, corner geometry and end preparation against the fabrication drawing. Connection fit and section properties require the exact profile; nominal envelope dimensions alone are insufficient. At nominal geometry and 7850 kg/m³ steel density, the reference is 21.478 kg per metre. This calculation excludes tolerances, coatings, corner radii and process losses; it is not certified shipping weight or a load rating. Compared with 150 × 150 × 4 mm, the nominal geometric reference is 17.1% higher on the same basis. This comparison supports quantity planning; it does not establish interchangeability.
Buying Square hollow sections 120 × 120 × 6 mm and requesting a price
The price for Square hollow sections 120 × 120 × 6 mm depends on the material specification, quantity, production or processing requirements, inspection, packing, freight and delivery schedule. Compare offers on the same technical specification and delivery basis; confirm availability and quotation validity before ordering.
For buying and price enquiries for Square hollow sections 120 × 120 × 6 mm, specify your delivery destination: Georgia (including Tbilisi), Turkey (including Ankara and Istanbul), the United Arab Emirates (UAE, including Dubai), Kuwait, Oman or Qatar. Send the required quantity, grade or chemical analysis, dimensions and inspection scope. Freight, delivery terms and shipment timing affect the quotation; supply options and destination documentation require confirmation before an order is agreed.
Preparing an enquiry for Square hollow sections 120 × 120 × 6 mm
Include Square hollow sections 120 × 120 × 6 mm, the required grade and complete standard designation, order quantity, length or coil limits where applicable, inspection documents and the exact delivery destination. Confirm traceability, packing, commercial terms and the shipment schedule with EMRA Steel.
Choose the product specification first; destination and shipment details belong in the delivery enquiry. Destination enquiry guides
Grade enquiries for Square hollow sections 120 × 120 × 6 mm
Square hollow sections 120 × 120 × 6 mm S355J2H
For Square hollow sections 120 × 120 × 6 mm S355J2H, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
