Review Heavy steel plate for the 20 × 1250 × 6000 mm specification. Check material grade, dimensions, inspection documents and delivery requirements before requesting a quotation.
Geometric estimates exclude rolling tolerances, coatings and process losses; hollow and rolled-section references include their own section-table basis. Calculated bar weights use unrounded mass. Values are not measured shipment weights. Confirm length, grade, manufacturing route, packing and supply in the offer; the existing image illustrates the product family.
Reference dimensions: 20 × 1250 × 6000 mm. At a nominal steel density of 7850 kg/m³, calculated mass is approximately 1177.5 kg per piece. Actual weighing, dimensional tolerances, grade and inspection requirements must be agreed before ordering. 20 × 1250 × 6000 mm
Heavy steel plate 20 × 1250 × 6000 mm Technical and buying guide
EMRA Steel
Review Heavy steel plate for the 20 × 1250 × 6000 mm specification. Check material grade, dimensions, inspection documents and delivery requirements before requesting a quotation.Read more
Standards and applicability
EN 10029 controls plate dimensional and shape tolerances; EN 10025-2 controls the selected structural grade. Numeric rows use the thickness of this plate; the hub compares thickness bands. S235JR and S275JR differ from S355J2, including the impact test temperature. Agree delivery condition, test orientation, impact applicability, flatness, edge condition and any ultrasonic test. Do not apply section elongation values to wide plate.
Mechanical reference table
Mechanical reference table
Grade / material
Scope / condition
Re / Rp0.2 (MPa)
Rm (MPa)
A min. (%)
Impact reference
S235JR
16 < t ≤ 40 mm
≥225
360–510
—
27 J / +20°C
S275JR
16 < t ≤ 40 mm
≥265
410–560
—
27 J / +20°C
S355J2
16 < t ≤ 40 mm
≥345
470–630
—
27 J / −20°C
Chemical composition references
Chemical composition references
Grade / material
Scope / condition
C (%)
Mn (%)
Si (%)
P (%)
S (%)
Cr / CEV (%)
S235JR
16 < t ≤ 40 mm
≤0.17
≤1.40
—
≤0.035
≤0.035
—
S275JR
16 < t ≤ 40 mm
≤0.21
≤1.50
—
≤0.035
≤0.035
—
S355J2
16 < t ≤ 40 mm
≤0.20
≤1.60
≤0.55
≤0.025
≤0.025
—
Selected percentages by mass and test values are reference requirements within the stated scope, not the actual heat analysis or a complete specification. A dash means no value is declared here, not zero. Compare the offered heat and test results with the applicable specification and inspection document. If EN 10204 type 3.1 is required, agree document availability, heat traceability and test scope before ordering.
Inspection and export enquiry
Send the exact product, size, full grade and standard edition, delivery condition, quantity, test requirements and named destination. Confirm cutting, coating, bundle or coil mass, protection, unloading and the Incoterms delivery point in the quotation. The destination guidance below supports port and inland comparisons; it does not confirm local stock or a fixed price.
Chemistry references and commercial grades
St37, St44 and St52 · historical DIN 17100 reference
Ladle-analysis reference for St37-2, St44-2 and St52-3 at t ≤16 mm only. Bare St37/St44/St52 names need a suffix, edition and delivery condition. Other thicknesses and product analysis have different rules. These legacy grades are not automatically equivalent to EN grades or interchangeable with CK45/CK60. For semi-finished feedstock, agree chemistry and downstream qualification separately.
St37, St44 and St52 · historical DIN 17100 reference
Grade / commercial type
C (%)
Mn (%)
Si (%)
P (%)
S (%)
St37-2 / 1.0037
≤0.17
—
—
≤0.050
≤0.050
St44-2 / 1.0044
≤0.21
—
—
≤0.050
≤0.050
St52-3 / 1.0570
≤0.20
≤1.60
≤0.55
≤0.040
≤0.040
Reference values are not shipment analysis or an inventory promise. Agree the complete specification, sampling basis, test methods and acceptance limits before ordering; confirm actual results on the heat/lot certificate. A dash means no numeric limit is stated in this selected reference, not zero.
Size specifications: Heavy steel plate 20 × 1250 × 6000 mm
Reference dimensions: 20 × 1250 × 6000 mm. At a nominal steel density of 7850 kg/m³, calculated mass is approximately 1177.5 kg per piece. Actual weighing, dimensional tolerances, grade and inspection requirements must be agreed before ordering. 20 × 1250 × 6000 mm
Choosing this specification
For 20 × 1250 × 6000 mm, agree the dimension order and whether the material is supplied as coil or cut lengths. Check usable width, cutting layout and flatness before comparing yield; nominal geometry does not include trimming or process losses. At nominal geometry and 7850 kg/m³ steel density, the reference is 1177.500 kg per piece. This calculation excludes tolerances, coatings, corner radii and process losses; it is not certified shipping weight or a load rating. Compared with 20 × 1220 × 12000 mm, the nominal geometric reference is 48.8% lower on the same basis. This comparison supports quantity planning; it does not establish interchangeability.
Grades, standards and inspection requirements for this product: Heavy steel plate
Buying Heavy steel plate 20 × 1250 × 6000 mm and requesting a price
The price for Heavy steel plate 20 × 1250 × 6000 mm depends on the material specification, quantity, production or processing requirements, inspection, packing, freight and delivery schedule. Compare offers on the same technical specification and delivery basis; confirm availability and quotation validity before ordering.
For buying and price enquiries for Heavy steel plate 20 × 1250 × 6000 mm, specify your delivery destination: Georgia (including Tbilisi), Turkey (including Ankara and Istanbul), the United Arab Emirates (UAE, including Dubai), Kuwait, Oman or Qatar. Send the required quantity, grade or chemical analysis, dimensions and inspection scope. Freight, delivery terms and shipment timing affect the quotation; supply options and destination documentation require confirmation before an order is agreed.
Preparing an enquiry for Heavy steel plate 20 × 1250 × 6000 mm
Include Heavy steel plate 20 × 1250 × 6000 mm, the required grade and complete standard designation, order quantity, length or coil limits where applicable, inspection documents and the exact delivery destination. Confirm traceability, packing, commercial terms and the shipment schedule with EMRA Steel.
Choose the product specification first; destination and shipment details belong in the delivery enquiry. Destination enquiry guides
Grade enquiries for Heavy steel plate 20 × 1250 × 6000 mm
Heavy steel plate 20 × 1250 × 6000 mm S235JR
For Heavy steel plate 20 × 1250 × 6000 mm S235JR, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Heavy steel plate 20 × 1250 × 6000 mm S275JR
For Heavy steel plate 20 × 1250 × 6000 mm S275JR, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
Heavy steel plate 20 × 1250 × 6000 mm S355J2
For Heavy steel plate 20 × 1250 × 6000 mm S355J2, confirm the complete material standard and edition, chemical analysis, delivery condition and inspection certificate. Review the offered material against the intended processing or project requirements. The designation is an enquiry reference; availability and equivalence to other grades require confirmation.
